Texas Instruments X-Loader 1.42-svn37646 BSP-dm37x-2.0-trunk for dm3730logic (2014-11-06 08:50:26) DRAM: 256MB (MT29C4G48MAZAPAKQ5) Booting from NAND NAND: in-chip ECC SgnP image: 0x6f160 bytes read from NAND at offset 0x80000 to 80400000 U-Boot 2011.06 BSP-dm37x-2.4-3 (Apr 20 2015 - 11:59:08) OMAP3630/3730-GP ES2.1, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz Logic DM37x/OMAP35x reference board + LPDDR/NAND I2C: ready DRAM: 256 MiB Board: DM37xx Torpedo Enable battery backup charger (BB_CFG = 0x1c) NAND: 512 MiB NAND: Internal to NAND ECC selected Found '28' display panel In: serial Out: serial Err: serial Product ID data cached to: 40200000 Die ID #069a00029ff80000016849aa10029018 OTG_SYSCONFIG: 00000001 - needs to be 00002001 ID data ROM : Gen 1 Part Number : 1017878 Model Name : SOMDM3730-20-2780AGCR-A Serial Number: 1212M00181 Data (writethrough) Cache is ON Net: smc911x-0 Hit any key to stop autoboot: 0 OMAP Logic # setenv otherbootargs ${otherbootargs} ip=192.168.120.155:::255.255.255.0:myboard:eth1:on OMAP Logic # saveenv Saving Environment to NAND... Erasing Nand... Erasing at 0x260000 -- 100% complete. Writing to Nand... done OMAP Logic # reset resetting ... Texas Instruments X-Loader 1.42-svn37646 BSP-dm37x-2.0-trunk for dm3730logic (2014-11-06 08:50:26) DRAM: 256MB (MT29C4G48MAZAPAKQ5) Booting from NAND NAND: in-chip ECC SgnP image: 0x6f160 bytes read from NAND at offset 0x80000 to 80400000 U-Boot 2011.06 BSP-dm37x-2.4-3 (Apr 20 2015 - 11:59:08) OMAP3630/3730-GP ES2.1, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz Logic DM37x/OMAP35x reference board + LPDDR/NAND I2C: ready DRAM: 256 MiB Board: DM37xx Torpedo Enable battery backup charger (BB_CFG = 0x1c) NAND: 512 MiB NAND: Internal to NAND ECC selected Found '28' display panel In: serial Out: serial Err: serial Product ID data cached to: 40200000 Die ID #069a00029ff80000016849aa10029018 OTG_SYSCONFIG: 00001008 - needs to be 00002001 ID data ROM : Gen 1 Part Number : 1017878 Model Name : SOMDM3730-20-2780AGCR-A Serial Number: 1212M00181 Data (writethrough) Cache is ON Net: smc911x-0 Hit any key to stop autoboot: 0 == Checking mmc1 for alternate boot script boot.scr == No MMC card found kernel_location: nand-part, rootfs_location: /dev, rootfs_type: yaffs == Loading kernel from nand partition kernel to 0x81000000 == Loading from nand0, offset 0x280000 Image Name: Linux-3.0.0-BSP-dm37x-2.4-3 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3944156 Bytes = 3.8 MiB Load Address: 80008000 Entry Point: 80008000 == rootfs located in /dev/mtdblock5 == == Kernel bootargs == nand-ecc=chip console=ttyO0,115200n8 display=28 ignore_loglevel early_printk no_console_suspend ip=192.168.120.155:::255.255.255.0:myboard:eth1:on mtdparts=omap2-nand.0:512k(x-loader),1664k(u-boot),384k(u-boot-env),5m(kernel),20m(ramdisk),-(fs) root=/dev/mtdblock5 rw rootfstype=yaffs2 bootm 0x81000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Linux-3.0.0-BSP-dm37x-2.4-3 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3944156 Bytes = 3.8 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Linux version 3.0.0-BSP-dm37x-2.4-3 (logic@logic-VirtualBox) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 Mon Apr 20 12:02:40 CDT 2015 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Logic DM37x Torpedo board [ 0.000000] omap3logic_product_id_set_location: ptr c0000274 size 568 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Reserving 4194304 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 [ 0.000000] On node 0 totalpages: 64512 [ 0.000000] free_area_init_node: node 0, pgdat c0921f3c, node_mem_map c0ec5000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 64000 pages, LIFO batch:15 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz [ 0.000000] Advisory 2.1: dpll5 rate is now 959833333 [ 0.000000] Reprogramming SDRC clock to 400000000 Hz [ 0.000000] dpll3_m2_clk rate change failed: -22 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64000 [ 0.000000] Kernel command line: nand-ecc=chip console=ttyO0,115200n8 display=28 ignore_loglevel early_printk no_console_suspend ip=192.168.120.155:::255.255.255.0:myboard:eth1:on mtdparts=omap2-nand.0:512k(x-loader),1664k(u-boot),384k(u-boot-env),5m(kernel),20m(ramdisk),-(fs) root=/dev/mtdblock5 rw rootfstype=yaffs2 [ 0.000000] omap3logic_display_selection:282 [ 0.000000] Standard display '28' 480:272:2:3:3:2:42:11:9000:1048576:16 [ 0.000000] omap3logic_display_selection: found panel '28' [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 252MB = 252MB total [ 0.000000] Memory: 240624k/240624k available, 21520k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .init : 0xc0008000 - 0xc0044000 ( 240 kB) [ 0.000000] .text : 0xc0044000 - 0xc0751004 (7221 kB) [ 0.000000] .data : 0xc0752000 - 0xc092fe30 (1912 kB) [ 0.000000] .bss : 0xc092fe54 - 0xc0ec417c (5713 kB) [ 0.000000] NR_IRQS:410 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3951 kB [ 0.000000] per task-struct memory footprint: 2304 bytes [ 0.001007] Calibrating delay loop... 594.49 BogoMIPS (lpj=2322432) [ 0.085937] pid_max: default: 32768 minimum: 301 [ 0.086608] Security Framework initialized [ 0.087005] Mount-cache hash table entries: 512 [ 0.092315] CPU: Testing write buffer coherency: ok [ 0.106781] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core [ 0.106811] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per [ 0.106811] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup [ 0.107299] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck. [ 0.147460] print_constraints: dummy: [ 0.147979] cpufreq_core_init:1887 [ 0.149780] NET: Registered protocol family 16 [ 0.150756] GPMC revision 5.0 [ 0.156799] omap_device: omap_gpio.0: new worst case activate latency 0: 122070 [ 0.159393] OMAP GPIO hardware version 2.5 [ 0.161102] OMAP GPIO hardware version 2.5 [ 0.162811] OMAP GPIO hardware version 2.5 [ 0.164550] OMAP GPIO hardware version 2.5 [ 0.166137] OMAP GPIO hardware version 2.5 [ 0.167846] OMAP GPIO hardware version 2.5 [ 0.171020] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.281555] omap3torpedo_fix_pbias_voltage:1341 PKUP_CTRL 0x40 [ 0.284942] omap3logic_lcd_init: name 28 data_lines 16 [ 0.289855] Setup pinmux and enable UART A [ 0.290740] omap_device: omap_uart.0: new worst case activate latency 0: 30517 [ 0.291351] omap_device: omap_uart.0: new worst case deactivate latency 0: 30517 [ 0.291809] Setup pinmux and enable UART B [ 0.293548] Setup pinmux and enable UART C [ 0.295318] omap3logic_product_id_move_data: product_id_data_location.ptr c0000274 [ 0.295349] arch/arm/mach-omap2/board-omap3logic-new-productid.c[343] [ 0.295379] U-boot provided product_id data is valid [ 0.295379] ID data ROM : Gen 1 [ 0.295410] Part Number : 1017878 [ 0.295410] Model Name : SOMDM3730-20-2780AGCR-A [ 0.295440] Serial Number: 1212M00181 [ 0.301086] _nand_init: id 0 nand_cs 0 [ 0.302032] registered isp1763 platform_device [ 0.307006] dm3730logic_camera_init: muxing 8-bit interface (cam_d0-cam_d7) [ 0.307647] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.321960] OMAP DMA hardware revision 5.0 [ 0.368438] bio: create slab at 0 [ 0.372100] machine_constraints_voltage: vwl1271: override min_uV, 1 -> 1800000 [ 0.372131] machine_constraints_voltage: vwl1271: override max_uV, 2147483647 -> 1800000 [ 0.372192] print_constraints: vwl1271: 1800 mV [ 0.372650] reg-fixed-voltage reg-fixed-voltage.1: vwl1271 supplying 1800000uV [ 0.375366] SCSI subsystem initialized [ 0.376556] omap_device: omap2_mcspi.1: new worst case activate latency 0: 61035 [ 0.377929] omap_device: omap2_mcspi.1: new worst case deactivate latency 0: 30517 [ 0.382141] usbcore: registered new interface driver usbfs [ 0.382690] usbcore: registered new interface driver hub [ 0.383544] usbcore: registered new device driver usb [ 0.386657] omap_device: omap_i2c.1: new worst case activate latency 0: 61035 [ 0.398712] omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz [ 0.443908] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 0.444213] twl4030: power (irq 373) chaining IRQs 376..383 [ 0.446685] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 0.449218] brf6300_dev_init [ 0.451843] omap_device: omap2_mcspi.1: new worst case activate latency 0: 122070 [ 0.459655] machine_constraints_voltage: VUSB1V5: override min_uV, 1 -> 1500000 [ 0.459686] machine_constraints_voltage: VUSB1V5: override max_uV, 2147483647 -> 1500000 [ 0.459716] print_constraints: VUSB1V5: 1500 mV normal standby [ 0.461944] machine_constraints_voltage: VUSB1V8: override min_uV, 1 -> 1800000 [ 0.461975] machine_constraints_voltage: VUSB1V8: override max_uV, 2147483647 -> 1800000 [ 0.462036] print_constraints: VUSB1V8: 1800 mV normal standby [ 0.464233] machine_constraints_voltage: VUSB3V1: override min_uV, 1 -> 3100000 [ 0.464263] machine_constraints_voltage: VUSB3V1: override max_uV, 2147483647 -> 3100000 [ 0.464324] print_constraints: VUSB3V1: 3100 mV normal standby [ 0.470367] Setting A idle... [ 0.478790] twl4030_usb twl4030_usb: Initialized TWL4030 USB module [ 0.481750] print_constraints: vdd_mpu_iva: 600 <--> 1450 mV normal [ 0.483825] print_constraints: vdd_core: 600 <--> 1450 mV normal [ 0.486328] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby [ 0.488769] print_constraints: VDAC: 1800 mV normal standby [ 0.491027] print_constraints: VDVI: 1800 mV normal standby [ 0.493682] print_constraints: VMMC2: 1850 <--> 3150 mV at 2600 mV normal standby [ 0.496551] print_constraints: VAUX1: 3000 mV normal standby [ 0.498870] print_constraints: VAUX3: 2800 mV normal standby [ 0.501434] print_constraints: vaux4: 1800 mV normal standby [ 0.502502] omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517 [ 0.515838] omap_i2c omap_i2c.2: bus 2 rev4.0 at 400 kHz [ 0.531463] omap_i2c omap_i2c.3: bus 3 rev4.0 at 400 kHz [ 0.535125] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.538543] Bluetooth: Core ver 2.16 [ 0.538879] NET: Registered protocol family 31 [ 0.538879] Bluetooth: HCI device and connection manager initialized [ 0.539276] Bluetooth: HCI socket layer initialized [ 0.539306] Bluetooth: L2CAP socket layer initialized [ 0.540222] Bluetooth: SCO socket layer initialized [ 0.543609] cfg80211: Calling CRDA to update world regulatory domain [ 0.549072] Switching to clocksource 32k_counter [ 0.555084] Switched to NOHz mode on CPU #0 [ 0.719482] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host) [ 0.720123] omap_device: musb-omap2430.-1: new worst case activate latency 0: 30517 [ 0.720550] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 0.720581] musb-hdrc: MHDRC RTL version 1.800 [ 0.720581] musb-hdrc: setup fifo_mode 4 [ 0.720611] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 0.722290] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 [ 0.723541] NET: Registered protocol family 2 [ 0.724609] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.727447] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.727905] TCP bind hash table entries: 8192 (order: 6, 360448 bytes) [ 0.732330] TCP: Hash tables configured (established 8192 bind 8192) [ 0.732543] TCP reno registered [ 0.732604] UDP hash table entries: 128 (order: 1, 12288 bytes) [ 0.732971] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes) [ 0.734405] NET: Registered protocol family 1 [ 0.735626] omap_device: omap_i2c.1: new worst case activate latency 0: 122070 [ 0.736846] omap_device: omap_i2c.1: new worst case deactivate latency 0: 122070 [ 0.739349] omap_device: musb-omap2430.-1: new worst case deactivate latency 0: 122070 [ 0.741210] RPC: Registered named UNIX socket transport module. [ 0.741241] RPC: Registered udp transport module. [ 0.741241] RPC: Registered tcp transport module. [ 0.741271] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.741455] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.746154] omap-iommu omap-iommu.0: isp registered [ 0.934600] VFS: Disk quotas dquot_6.5.2 [ 0.934722] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.938720] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.940002] yaffs: yaffs built Apr 20 2015 12:02:04 Installing. [ 0.940185] msgmni has been set to 469 [ 0.949859] io scheduler noop registered [ 0.949890] io scheduler deadline registered [ 0.950073] io scheduler cfq registered (default) [ 0.953369] Generic Backlight Driver Initialized. [ 1.018463] OMAP DSS rev 2.0 [ 1.029327] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.036743] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 2.150634] console [ttyO0] enabled [ 2.156158] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 2.165679] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 [ 2.205169] brd: module loaded [ 2.224212] loop: module loaded [ 2.234039] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.241821] omap2-nand driver initializing [ 2.247528] nand_get_flash_type: disturb cf740000 chipsize 536870912 erasesize 131072 [ 2.255920] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron NAND 512MiB 1,8V 16-bit) [ 2.265136] NAND ECC: HW_CHIP [ 2.268463] 6 cmdlinepart partitions found on MTD device omap2-nand.0 [ 2.275238] Creating 6 MTD partitions on "omap2-nand.0": [ 2.280975] 0x000000000000-0x000000080000 : "x-loader" [ 2.295288] 0x000000080000-0x000000220000 : "u-boot" [ 2.306884] 0x000000220000-0x000000280000 : "u-boot-env" [ 2.317504] 0x000000280000-0x000000780000 : "kernel" [ 2.331909] 0x000000780000-0x000001b80000 : "ramdisk" [ 2.360168] 0x000001b80000-0x000020000000 : "fs" [ 2.824981] smsc911x: Driver version 2008-10-21 [ 2.837188] smsc911x-mdio: probed [ 2.841430] smsc911x smsc911x.0: eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=0:01, irq=-1) [ 2.852935] smsc911x smsc911x.0: eth0: MAC Address: 00:08:ee:06:3e:99 [ 2.860656] usbcore: registered new interface driver asix [ 2.866821] usbcore: registered new interface driver cdc_ether [ 2.873352] usbcore: registered new interface driver net1080 [ 2.879699] usbcore: registered new interface driver cdc_subset [ 2.886322] usbcore: registered new interface driver zaurus [ 2.892211] cdc_ncm: 01-June-2011 [ 2.896087] usbcore: registered new interface driver cdc_ncm [ 2.902160] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.910064] devflags passed by probe: 0x00000004 [ 2.945404] hwmode pullup disable [ 2.949005] isp1763: SRAM mode, 16 bit bus width [ 2.953857] Resetting ISP1763... [ 2.958374] Reset done [ 3.201751] ISP1783 using host mode [ 3.205444] otg_set_role() switching to HOST role [ 3.210449] isp1763 initialization successfully [ 3.215301] ISP1763 USB device initialised [ 3.220062] Registered host as active driver [ 3.224670] isp1763 isp1763: ST-Ericsson ISP1763 USB Host Controller [ 3.234069] isp1763 isp1763: new USB bus registered, assigned bus number 1 [ 3.241546] isp1763 isp1763: bus width: 16 [ 3.346466] isp1763 isp1763: USB ISP 1763 HW rev. 32 started [ 3.353759] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.361053] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.368743] usb usb1: Product: ST-Ericsson ISP1763 USB Host Controller [ 3.375671] usb usb1: Manufacturer: Linux 3.0.0-BSP-dm37x-2.4-3 isp1763-hcd [ 3.383056] usb usb1: SerialNumber: isp1763 [ 3.392089] hub 1-0:1.0: USB hub found [ 3.396759] hub 1-0:1.0: 1 port detected [ 3.405242] isp1763 host controller driver loaded [ 3.410339] Initializing USB Mass Storage driver... [ 3.416015] usbcore: registered new interface driver usb-storage [ 3.422454] USB Mass Storage support registered. [ 3.428253] usbcore: registered new interface driver usbtest [ 3.435913] mousedev: PS/2 mouse device common for all mice [ 3.450958] input: TSC2004 Touchscreen as /devices/platform/omap/omap_i2c.3/i2c-3/3-0048/input/input0 [ 3.463867] i2c-core: driver [tsc2004] using legacy resume method [ 3.473022] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 [ 3.495727] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 3.504089] twl_rtc twl_rtc: Power up reset detected. [ 3.510620] twl_rtc twl_rtc: Enabling TWL-RTC. [ 3.516510] i2c /dev entries driver [ 3.523834] Linux media interface: v0.10 [ 3.529327] lirc_dev: IR Remote Control driver registered, major 251 [ 3.536468] IR NEC protocol handler initialized [ 3.541259] IR RC5(x) protocol handler initialized [ 3.546417] IR RC6 protocol handler initialized [ 3.551269] IR JVC protocol handler initialized [ 3.556030] IR Sony protocol handler initialized [ 3.560974] IR RC5 (streamzap) protocol handler initialized [ 3.566925] IR LIRC bridge handler initialized [ 3.571594] Linux video capture interface: v2.00 [ 3.578674] omap3isp omap3isp: Revision 15.0 found [ 3.584350] omap-iommu omap-iommu.0: isp: version 1.1 [ 3.666931] ov7690 3-0021: OV7690 not detected, wrong manufacturer or version [ 3.678741] isp_register_subdev_group: Unable to register subdev ov7690 [ 3.688659] mt9p031 2-0048: MT9P031 not detected, wrong version 0xffffff87 [ 3.696807] isp_register_subdev_group: Unable to register subdev mt9p031 [ 3.710144] usbcore: registered new interface driver uvcvideo [ 3.716369] USB Video Class driver (v1.1.0) [ 3.721221] Driver for 1-wire Dallas network protocol. [ 3.727813] omap_hdq omap_hdq.0: OMAP HDQ Hardware Rev 0.5. Driver in Interrupt mode [ 3.799560] usb 1-1: new high speed USB device number 2 using isp1763 [ 3.936676] omap_device: omap_wdt.-1: new worst case activate latency 0: 30517 [ 3.946044] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 3.952575] omap_device: omap_wdt.-1: new worst case deactivate latency 0: 30517 [ 3.960784] Bluetooth: BRF6300 SPI Bluetooth driver ver 0.1 [ 3.970855] cpuidle: using governor ladder [ 3.975341] cpuidle: using governor menu [ 4.005065] usb 1-1: New USB device found, idVendor=0471, idProduct=3526 [ 4.012268] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4.019866] usb 1-1: Product: ISP1520 [ 4.023712] usb 1-1: Manufacturer: Philips Semiconductors [ 4.032379] hub 1-1:1.0: USB hub found [ 4.036987] hub 1-1:1.0: 2 ports detected [ 4.182220] power_supply bq27000-battery: driver failed to report `voltage_now' property [ 4.191986] bq27000-battery bq27000-battery: support ver. 1.2.0 enabled [ 4.285461] Registered led device: led1 [ 4.290100] Registered led device: led2 [ 4.372833] Registered led device: led3 [ 4.379119] usbcore: registered new interface driver usbhid [ 4.385528] usbhid: USB HID core driver [ 4.393646] usbcore: registered new interface driver snd-usb-audio [ 4.406005] OMAP3 Logic DM37x/OMAP35x SOM LV/Torpedo SoC init [ 4.479553] usb 1-1.2: new high speed USB device number 3 using isp1763 [ 4.509643] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok [ 4.524475] ALSA device list: [ 4.527801] #0: omap3logic [ 4.530822] oprofile: hardware counters not available [ 4.536224] oprofile: using timer interrupt. [ 4.541809] TCP cubic registered [ 4.545440] Initializing XFRM netlink socket [ 4.551208] NET: Registered protocol family 17 [ 4.556091] NET: Registered protocol family 15 [ 4.562561] Bluetooth: RFCOMM TTY layer initialized [ 4.567993] Bluetooth: RFCOMM socket layer initialized [ 4.573486] Bluetooth: RFCOMM ver 1.11 [ 4.577667] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.583374] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.590911] Registering the dns_resolver key type [ 4.597839] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 4.606414] ThumbEE CPU extension supported. [ 4.640808] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 4.650543] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 4.659912] SmartReflex Class3 initialized [ 4.664245] sr_start_vddautocomp: sr->srid 1 [ 4.669067] omap_device: smartreflex.1: new worst case activate latency 0: 152587 [ 4.677093] sr_start_vddautocomp: sr->srid 0 [ 4.755218] clock: disabling unused clocks to save power [ 4.765167] power_supply bq27000-battery: driver failed to report `voltage_now' property [ 4.783935] Console: switching to colour frame buffer device 60x34 [ 4.810150] usb 1-1.2: New USB device found, idVendor=0b95, idProduct=772a [ 4.817504] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.826446] usb 1-1.2: Product: AX88x72A [ 4.830688] usb 1-1.2: Manufacturer: ASIX Elec. Corp. [ 4.835998] usb 1-1.2: SerialNumber: 000002 [ 5.168151] omap_device: smartreflex.0: new worst case deactivate latency 0: 183105 [ 5.247619] omap_device: omap_i2c.1: new worst case activate latency 0: 183105 [ 5.257049] regulator_init_complete: VDAC: incomplete constraints, leaving on [ 5.272796] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801) [ 5.282379] omap_vout omap_vout: Buffer Size = 3686400 [ 5.291748] omap_vout omap_vout: : registered and initialized video device 15 [ 5.299530] omap_vout omap_vout: Buffer Size = 3686400 [ 5.307891] omap_vout omap_vout: : registered and initialized video device 16 [ 5.450042] dm3730_torpedo_bl_set_intensity: level 178 (69% on) [ 5.456481] dm3730_torpedo_bl_set_intensity: turn on GPIO_154 as backlight! [ 5.693511] asix 1-1.2:1.0: eth1: register 'asix' at usb-isp1763-1.2, ASIX AX88772 USB 2.0 Ethernet, 00:06:a7:e0:17:98 [ 6.332183] asix 1-1.2:1.0: eth1: link down [ 7.332916] asix 1-1.2:1.0: eth1: link up, 100Mbps, full-duplex, lpa 0xCDE1 [ 7.363372] IP-Config: Complete: [ 7.366821] device=eth1, addr=192.168.120.155, mask=255.255.255.0, gw=255.255.255.255, [ 7.375579] host=myboard, domain=, nis-domain=(none), [ 7.381500] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 7.408111] yaffs: dev is 32505861 name is "mtdblock5" rw [ 7.414001] yaffs: passed flags "" [ 7.417755] yaffs: yaffs: Attempting MTD mount of 31.5,"mtdblock5" [ 7.425079] yaffs: oobavail(16) <= 28; forcing "tags-ecc-off" [ 8.999237] smartreflex smartreflex.0: sr_v2_disable: Smartreflex disable timedout [ 16.298461] yaffs: yaffs_read_super: is_checkpointed 0 [ 16.304931] VFS: Mounted root (yaffs2 filesystem) on device 31:5. [ 16.311706] Freeing init memory: 240K Mounting /proc and /sys Starting the hotplug events dispatcher udevd Synthesizing initial hotplug events [ 17.128631] udevd (62): /proc/62/oom_adj is deprecated, please use /proc/62/oom_score_adj instead. Setting the hostname to DM-37x Run depmod to create modules.dep.bin Loading module g_ether [ 28.914001] g_ether gadget: using random self ethernet address [ 28.920318] g_ether gadget: using random host ethernet address [ 28.929016] usb0: MAC 6e:b5:22:eb:89:c9 [ 28.933197] usb0: HOST MAC 3a:bf:99:80:aa:62 [ 28.937744] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 28.944885] g_ether gadget: g_ether ready [ 28.949188] musb-hdrc musb-hdrc: MUSB HDRC host driver [ 28.955291] musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2 [ 28.963684] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 28.970825] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 28.978515] usb usb2: Product: MUSB HDRC host driver [ 28.983795] usb usb2: Manufacturer: Linux 3.0.0-BSP-dm37x-2.4-3 musb-hcd [ 28.991119] usb usb2: SerialNumber: musb-hdrc [ 28.998016] hub 2-0:1.0: USB hub found [ 29.002166] hub 2-0:1.0: 1 port detected Mounting filesystems [ 29.487121] usb 2-1: new high speed USB device number 2 using musb-hdrc [ 29.643951] usb 2-1: device v050d p0233 is not supported [ 29.649536] usb 2-1: New USB device found, idVendor=050d, idProduct=0233 [ 29.656707] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 29.667510] hub 2-1:1.0: USB hub found [ 29.733062] hub 2-1:1.0: 4 ports detected Starting syslogd and klogd Enabling SmartReflex: Running sysctl to fix ARP flux when using multiple interfaces Starting the haveged entropy pool maintainer: Starting inetd: Starting the dropbear ssh server: Setting up touch handler and default /etc/pointercal Starting pwr-button: Using /dev/input/event1 for S2 power button input device DirectFB: Setup DirectFB for touch input Restoring ALSA state for soundcard omap3logic Enabling PM off mode: Welcome to the LTIB Embedded Linux Environment !!!!! WARNING !!!!!!! The default password for the root account is: root please change this password using the 'passwd' command and then edit this message (/etc/issue) to remove this message. To enable DHCP on ethernet, type "ifup eth0" DM-37x login: root Password: [ 35.050689] smartreflex smartreflex.0: sr_v2_disable: Smartreflex disable timedout DM-37x# ifconfig eth1 Link encap:Ethernet HWaddr 00:06:A7:E0:17:98 inet addr:192.168.120.155 Bcast:192.168.120.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:230 (230.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) DM-37x#